How To Install Wood On Windows For Hurricane

Hurricane is a natural occurrence that can damage things inside your home. Only to reduce the problem it could cause, using touch on-resistant windows are the best measure to take, particularly during big storms or hurricanes. But when yours is not a resistant type, then y'all need to board up your window.

Does the idea of boarding up the windows from the inside give you worries? If it does, I can assure youthat boarding windows with plywood costvery little.

Desire to know about the steps required for boarding up your abode against a hurricane? This guide will direct you properly on the best ways to board up windows for hurricane.

Step By Stride Approach to Boarding up Windows on Vinyl Sliding

Step 1: Measure Correctly The Dimension Of The Window

A measuring tape is the best tool to get the dimension of a window. Run the tape around the window you want to board and accept down the measurements. If the window has a frame, measure from the top of the frame downwardly to its bottom.

Take measurements, both horizontally and vertically. The aim of taking measurements is to determine the dimension of boarding window plywood costrequired for the job.

Footstep 2: Get the Size of Plywood Yous Need For the Window

Specifically, plywood usually comes in 4 by 8 feet or 1.2 by ii.4 m. Some windows surpass this size with a few dimensions. If your window is 1 of those, then I advise you join ii pieces of plywood together.

Joining two pieces of plywood is not a difficult task. What you need for the job is a two by 4″ brace, 6 screws (2.25in or 5.7cm), and a drill.

Bring the two pieces of plywood side by side, so that they impact. Place the 2 by iv″ brace along with the middle bespeak of the two plywoods. Drill in the six screws (2 at the top, two at the middle, and two at the lesser). The screws ensure that the two pieces join perfectly.

Getting the amount of plywood that would effectively lath up your house is tricky. This happens nearly times when y'all don't know how much boarding a window with plywood costs. Hence to do this effectively, add 20cm (8″) to the measurements you got from your window. If you got 100cm by 60cm or l″ by 35″, and then you need to cut out 120cm past 80cm or 58″ by 43″ of plywood.

For a window with an extended frame, only add one-half of the above dimension. Add 10cm or 4″ to the window size earlier cutting the wood.

You could either cut the plywood by yourself using a saw or ship the plywood and measurements down to a carpenter.

Pace 3. Find the Point Of Zipper of the Window Frame and the Wall

Call up, your window frame is attached to the wall by some wooden protrusions from the frame. These protrusions are usually 10cm or iv″ in length and jut out from both sides of a window frame.

A useful tip: To observe these protrusions or studs, find the blast head within the frame.

Drill holes into the plywood, just when doing this, accept into consideration the studs/protrusions which adhere the frame to the wall. Brand sure that the holes align with the studs.

The ideal screw for this procedure is a quarter-inch or 0.64cm pan head or lag screws. On the four edges of the plywood, you take to make holes on them.

Ensure to drill these holes at a distance of 5.1cm or 2″ from the edge of the plywood and through it. Likewise, consider the size of the screw before yous drill. Keep in listen that making a hole bigger or smaller than the screw would non requite a better result.

You should brand holes that run from top to bottom and left to right at 30cm or 12″ intervals. These holes should exist on the same line with the holes already at the edges to make screwing easy. For windows with an extended bottom frame, you but need to drill holes at the top and sides.

Step 4:Screw-In Plywood Past Placing Over Window Frame

For this step, you lot need a pan head or lag screw and an assistant. Ensure to use ¼ or 0.64cm pan caput or lag screws for this. This screw is platonic considering their flat heads would not destroy your wood. The assistant is to help you hold information technology while you screw.

The screw should penetrate at least 2″ or five.1cm to ensure the plywood fastens tight. One time you have done this, you surely created a potent window guard for your dwelling against hurricane

Steps in Boarding up Windows on Masonry House

Step one. Take Dimension of the Window

Using a measuring tape, take the right dimension of the window to be boarded upwards. Since it is a masonry house, take your measurements from within the frame. Measure out elevation to lesser and side to side. Write down your measurements.

Step 2. Shape Plywood to Equal the Dimension of Your Window

Cutting the plywood to shape using the dimensions taken from your window. The measurement of the plywood should be the aforementioned every bit the window then that it fits perfectly into the frame.

For example, measured window dimension 100cm by 60cm, the plywood dimension should also be 100cm by 60cm. Practise not add or remove any inch or cm.

Plywood should exist shaped to exact measurements using a saw. In a situation where you practise non have a saw or uncomfortable using yours, visit a carpenter for help.

3. Join Two Pieces of Plywood

In cases where your window dimension is larger than the plywood standard dimension (four by 8ft), adhere two pieces of plywood.

For this procedure, you would need a 2 by a 4-inch caryatid and six 2.25″ or 5.7cm screws. Identify the brace at the midpoint between the ii pieces of wood.

Spiral-in the six screws (ii at the top, two at the center, and ii at the bottom). This procedure is to ensure that the two pieces of wood would non pull autonomously.

4. Fasten Window Clips to the Sides of the Plywood

You will demand two pairs of clips for this process. The clips on the same side should be set at 2ft or 0.61m autonomously. So now that they are facing you, attach the clips to the plywood by tapping with a hammer. Using a hammer might be optional, only it is necessary as it makes the clips connect firmly to the wood.

Also, make sure that the clips on both sides are spaced equally and facing each other for optimum functioning.

5. Attach Plywood to Window Frame

The tightness of the prune is to the plywood is a significant determiner of how secure your home would exist during the hurricane. When attaching the frame, the all-time manner hurricane clips piece of work on windows is to ensure that information technology attach firmly to the frame.

To prevent your plywood from falling to tempest or hurricane, ensure to attach the clip firmly to the frame. To detach the plywood at the cease of the season, push button downward the board and pull up clips simultaneously.

Wrap Up

Protecting your dwelling house from hurricane shouldn't be a daunting job for you. You can do it all by yourself with little if you know the best ways to board upward windows for hurricane.Whether you are using a sliding window on any other types, to protect your domicile, follow the steps listed beneath.

To board up windows on a vinyl sliding you lot should:

• Measure the window
• Cutting the plywood while adding 20cm or eight″ to the measurement gotten from the window
• Find the points that attach the window frame to the wall
• Drill the wood according to the altitude between points of attachment
• Attach forest to the window by screwing in

But if you using a brick house, to board upwards windows on masonry walls require you to:

• Measure the window
• Cut the plywood to the exact dimension of the window

That'south it. Have fun protecting your house from hurricane.

Source: https://www.wcmanet.org/how-to-board-up-windows-for-hurricane/

Posted by: comptonwhicily74.blogspot.com

Share this post