Download Article

Download Article

Different traditional vertical blinds or shades, Roman shades are each made from 1 unmarried piece of material. Roman shades enhance and lower vertically, and when they are raised, the slice of fabric elegantly folds over itself. Yous can install a new prepare of Roman shades over the course of 3 or 4 hours. The shades can be installed in one of ii ways: either using an interior mount, where the shades are hung inside of the window frame, or using an exterior mount, where shades are attached to the wall above the window.

  1. one

    Choose an interior mount if you lot accept sturdy, square window frames. An interior mount involves hanging the shades inside of the window frame. This is a good selection if your window frames are deeper than 3–four inches (7.half dozen–ten.2 cm). When you use an interior mounting way, you'll attach the Roman shades to the downward-facing surface on the upper interior of the window frame (often called the frame's "ceiling").[one]

    • Mounting your Roman shades in the interior mode is a good choice if y'all have strong window frames that can carry the weight of the heavy shades.
    • An interior mount also gives a more finished look, and it doesn't comprehend upward the top of the window-frame molding.

  2. 2

    Check if the window frame is level before mounting the brackets. Equally a result of one-time age or poor construction, window frames ofttimes have a slightly uneven "ceiling." Utilise a level to test whether or not the frame is even. Concord the level upwards against the frame'due south "ceiling," and make sure that the small bubble is clearly in the middle of the marked section on the tool.[2]

    • If you lot're using an exterior mountain, you lot won't need to check that the frame itself is level, since you won't be attaching the shade to the frame.

    Advertisement

  3. 3

    Shim the frame if it's non level so your Roman shades hang evenly. If your frame ceiling is not level, you will demand to insert a couple small shims to even it out. Brainstorm by using a hammer to pry off the molding from around the edges of your window frame. Then, identify the tapered end of a shim betwixt the window frame and the wall on the low (sagging) terminate of the frame. Lightly tap the shim in by at least one⁄2  in (i.3 cm) to raise that side of the frame. Use your level to see if the frame is evened out afterwards every iii-iv hammer taps.[3]

    • A shim is a thin, angled piece of wood that will brand the ceiling level when nailed in place. You can purchase shims at any hardware store or home-comeback shop.
    • Once the window frame is level, snap off the ends of the shims that are sticking out past the end of the frame. Then, utilise your hammer to reattach the molding around the window frame. Y'all should exist able to stick the nails back in the same holds that you pried them out of earlier.

  4. 4

    Measure the shade's headrail with a record measure. The shade'southward headrail is the long superlative metal piece of the shade, from which the material shades themselves descend. Measuring the headrail volition help you find the location where you'll mount the brackets that agree upwards the headrail. Hook the metal prong of your tape measure and extend the tape to the far end of the headrail. Then utilize the tape measure out to find the width of the interior of your window frames.[iv]

    • Note that if the headrail is longer than the window frame is wide, y'all must use an outside mount.

  5. five

    Mark the ii bracket locations on the frame with a pencil. Extend your tape measure to the verbal length of the headrail, and hold it upward inside of the window frame, against the frame'southward "ceiling." Lightly mark the endpoints of the headrail. So, measure in three inches (7.six cm) on either side of the headrail's endpoints. Mark these ii spots with a pencil. These markings will point where you'll hang the 2 brackets.[v]

    • For instance, say that the headrail measures 24 inches (61 cm) long. To find the locations for the brackets, measure in iii inches (7.vi cm) on either side. So, yous'll identify 1 mark at the 3 in (seven.6 cm) signal and another at the 21 in (53 cm) signal.
    • Once you've marked the locations for the brackets, you can erase the calorie-free markings that indicated the endpoints of the headrail.

  6. 6

    Place an "X" on the 2 screw locations for each of the brackets. Selection up ane of the C-shaped metal brackets and hold it in place on top of the pencil markings you just drew. The bracket should have 2 screw holes. Use your pencil to identify a small "10" in each of the holes. You'll utilize these markings to insert the screws that agree the brackets in identify.[6]

    • Then, echo the process, property the bracket upwards in the 2nd bracket location that you marked earlier. Use a pencil to marking the 2 locations where you'll insert screws to hold the 2nd subclass in place.

  7. 7

    Drill pilot holes up into the "ceiling" of the window frame. Insert a 1⁄8  in (0.32 cm) drill bit into your electric drill. Hold the drill vertically with the bit pointing upward, so that the tip touches i of the "Ten" spots you just marked. Drill a pilot hole in each of the four marked locations. Drill each pilot pigsty 1 inch (2.5 cm) deep.[7]

    • If you didn't drill airplane pilot holes, the screws used to hold upwards the brackets would splinter the wood.

  8. 8

    Screw the brackets into the pilot holes with a screwdriver. Place each bracket on the marked location on the wall. Line up the brackets with the pilot holes that you just drilled in the window frame and skid the 2 screws through the holes in the brackets. Employ a screwdriver to screw them in place.[8]

    • Employ the brackets and screws that came with your Roman shades for installation. This makes installation more convenient and cheaper than if you lot had to buy new screws from a hardware shop.
    • Different brands of Roman shades may have slightly unlike installation methods. If you get confused, follow the specific directions that came with yours.

  9. 9

    Slide the shades into identify in the mounted brackets to secure them. Roman shades are outfitted with twin brackets that click into identify with the brackets you lot've attached to the wall. To install your shades, slide the top of the shades forward until the two brackets click into identify. Brand sure that the headrail is centered over the window.[9]

    • At this betoken, the shades should be secured in the frame. If you lot demand to remove them at a later date, only give a sharp tug in the direction opposite the mode you slid them into position.

  10. 10

    Drive a caput spiral into each end subclass to secure the shade. Elevator upwards the Roman shade and then that yous're looking beneath information technology at the bottom of the brackets. Pick upwards the short 2 in (5.1 cm) caput screws that came with the Roman shade kit and thread them into visible pigsty in each of the 2 brackets. Using your screwdriver again, tighten the head screw firmly into headrail.[ten]

    • These head screws will preclude the headrail from popping out of the subclass if y'all requite the cord too abrupt of a tug.

    Advertising

  1. i

    Use an exterior mount if the window frames are rectangular or shallow. Selecting an exterior mount makes the most sense if your frames are less than iii–4 inches (7.6–10.ii cm) deep. To discover out if your frames are rectangular, measure diagonally beyond your window frame with a tape measure. Starting time measure inside of the window frame from the top-right corner to the bottom-left corner. Then measure once again from the top-left corner to the bottom-right corner. Compare the 2 numbers to figure out if your window is square.[11]

    • If the 2 measurements differ past over 1⁄two  in (1.3 cm), your windows aren't square and you demand to use an external mount.
    • Outside mounts are helpful if yous would like to brand a window appear larger than it really is. An external frame is besides the best option if you lot take walls fabricated of a strong cloth, similar forest, brick, or concrete.
    • Also utilize an exterior mount if your window frame is worn or splintering and would like to cover it up.

  2. two

    Mensurate the headrail and mark the locations of the endcaps on the wall. The headrail is a long metallic upper slice of the shade that the shade'southward fabric comes downwards from. Accept the length measurement of your headrail and of the top of your window frame. Discover the midpoint of both distances, and heart your headrail to a higher place the window frame. Mark the location of both endcaps of the headrail on the wall with a pencil.[12]

    • Large Roman shades used in an outside mount may accept multiple metallic brackets to back up the shades' weight. In this example, the additional brackets will exist spaced evenly within the space between the 2 edge brackets located 3 inches (7.half dozen cm) in. Mark these locations on the frame or wall also.

  3. 3

    Mark 2 points iii in (7.six cm) in from the ends of the headrail. These points are where y'all'll heart the two brackets that hold up the Roman shade. Use your tape measure to measure 3 inches (seven.half dozen cm) in from each side of the measured length of the headrail. Then apply a pencil to mark both of the 2 locations on the wall above your window frame with a pocket-size "Ten."[13]

    • If your Roman shade headrail comes with multiple loose brackets, infinite them evenly over the top of the shade.

  4. 4

    Pre-drill pilot holes if you're installing shades onto drywall or plastic. With an exterior mount, you could be dealing with either of these types of materials. Since plastic and drywall are a little breakable, drilling straight into them could fracture the textile. To drill a airplane pilot pigsty, drill a hole through the wall above the frame using a 1⁄8  in (0.32 cm) drill scrap. Each of the 4 pilot holes you drill should exist 1 inch (ii.5 cm) deep.[14]

    • These screws and fasteners should be included with the Roman shade when you lot buy it. If not, you can buy them from a hardware shop.

  5. 5

    Utilize a carbide drill to drill pilot holes in concrete, stone, brick, or tile. These materials are dense and sturdy and a regular steel drill bit won't be able to penetrate them. If y'all are mounting your exterior Roman shades on ane of these substances, you'll need to use a 1⁄8  in (0.32 cm) carbide drill flake drill the pilot hole. Agree the drill so the bit is at a 90° angle to the wall, and drill the 4 pilot holes each 1 inch (ii.five cm) deep.[15]

    • Carbide is a type of coating that manufacturers put on the tip of steel bits to make them carbide bits. Carbide $.25 are sharper than ordinary steel bits, and will retain their sharpness fifty-fifty later drilling through concrete or brick.

  6. 6

    Spiral the brackets into the pilot holes with a screwdriver. Place i of the brackets in position so that its 2 holes line up with two of the pilot holes you just drilled. Set the tip of a screw in each of the holes. Then, using your screwdriver, turn the screws clockwise until they're held tight against the wall. Echo the procedure with the second bracket. At this point, you're almost finished![xvi]

    • Unless parts are missing from the shade-installation kit, you shouldn't need to buy any additional brackets or screws.
    • If you are installing your Roman shade in fabric other than wood, you volition demand different types of screws or fasteners. For case, yous will demand to apply hollow wall anchors or toggle bolts if you are hanging Roman shades in plastic or drywall.

  7. 7

    Adhere the shades' headrail to the wall by snapping it in to the brackets. For exterior-mounted Roman shades, the headrail should have ii indentations where information technology snaps onto the brackets. Bending the headrail upward and push button the top into the brackets, and so pull downward until the headrail snaps into place. This should secure the headrail (and fastened shades) in place.[17]

    • In some sets of shades, you may need to snap the headrail into place starting time and and then snap the shades into the headrail in one case it's in identify.
    • To remove the headrail at a later date, tilt the headrail down and give it a sharp tug out and away from the wall.

  8. viii

    Pull on the cord that adjusts the shades to raise or lower them. Give the cord a tug to verify that the shades are secure and functional. If the shades come away from the wall when you pull and release the string, check to brand sure that all screws and fasteners are tightened. You may as well need to snip off small-scale plastic loops holding the shade in its "closed" position.[xviii]

    • If y'all've opted for a fix of cordless Roman shades, y'all tin raise and lower the shades simply by grasping the handle behind the shade and raising or lowering it to the level you'd like it to exist at.[19]

    Advert

Add together New Question

  • Question

    On an exterior mount, should the shade width extend to the edges outside of the molding, or should I leave the molding exposed?

    Community Answer

    The width of the shade on an exterior mount should extend past the edges of the molding by about one-1/ii" to 2" on each side. This is suggested for security as in that location is usually a gap on each side caused simply past the shade'due south being mounted "outside" of the window frame (molding). The extra cloth is supposed to prevent that gap that could allow someone to see inside.

  • Question

    Tin Roman blinds be attached to a ceiling?

    Community Answer

    Yes, this is a proficient way to make a window look taller. You volition need to adhere a board or crossbar securely to the ceiling, then attach your blind to the board.

  • Question

    My shade came with no hardware. Where tin I purchase what I need?

    Community Answer

    Any hardware store, big or small has them. It would exist best to measure the "header" on your shade first to run across what size it is.

  • Question

    Should an exterior mount for a Roman shade lay flat on the glass?

    ConnorFisher

    ConnorFisher

    Community Reply

    No, it will non lay confronting the drinking glass. The shade will hang iv-half-dozen inches abroad from the glass, since the drinking glass pane itself is inset a few inches within the window frame. Interior mounting lets the shade hang much closer to the glass.

  • Question

    Is there method of installing roman shade brackets inside window frame on vertical (sides) of window frame?

    ConnorFisher

    ConnorFisher

    Customs Answer

    No, there is not. Roman shades are always a vertical type of shade, meaning that they always attach from the top of the window (or on the wall above) and hang downwards over the window.

  • Question

    I just removed window blinds that were falling apart. Would a roman bullheaded fit in the hardware left over from the old ones?

    ConnorFisher

    ConnorFisher

    Community Respond

    Possibly, information technology depends on if the brackets from your old shades are the same size and shape every bit needed to concur the headrail for the new roman shades. You lot're probably better off just using new hardware for the new shades. It'll most likely come with the roman-shade kit, and your old hardware may be worn out / weak anyway.

  • Question

    How exercise I install these on a curved window, and is it possible to do a side subclass install?

    Community Answer

    Piece of work out projects like this with newsprint before ordering materials. Roman shades that open up and close are traditionally horizontally and vertically straight. For a paladin window, place the the upper horizontal bracket across the window at the end of the window's arch. Leave the arch window space in a higher place open or cover it with similar fabric or sheer fabric folded like a fan and centered above the horizontal bracket to fill the space. This fabric would be stationary.

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

Things Y'all'll Demand

  • Tape mensurate
  • Roman shade
  • Hammer
  • Shims
  • Level
  • Ability drill
  • 1⁄viii  in (0.32 cm) drill bit
  • one⁄8  in (0.32 cm) carbide drill chip (optional)
  • Screwdriver
  • Wood screws
  • Pencil
  • Brackets
  • Fastener screws
  • Anchors
  • Toggle bolts

  • If you choose to use an outside mount, make sure that in that location's at to the lowest degree 2 inches (5.1 cm) of infinite between the pinnacle of the window frame and the ceiling above.[20]

  • Roman shades are considered a simple and stylish window covering that block sunlight and offering privacy. They tin can likewise be used to cover a window for winter. Roman shades that complement a variety of interior decoration styles will not detract from the remaining décor in the room.

Thanks for submitting a tip for review!

Advertizing

References

About This Article

Thank you to all authors for creating a folio that has been read 141,694 times.

Reader Success Stories

  • Anonymous

    "Let me know where to position rings and how many rings to use."

Did this article help you?