How To Break Down Colt 4 1/2" Match Target To Clean

smootik
Modelgun Perfectionist


Number of posts : 1823
Location / Country : Poland
Registration date : 2009-03-03

Subject: MGC Colt Woodsman Match Target (ABS) disassemblyFriday Jul xvi, 2022 ane:10 pm
Disassembly of Colt Woodsman is also not very usual. Until I received transmission I was non able to figure out how to do it correctly. Earlier y'all beginning, come across transmission in the next mail service as a reference. remove magazine, make sure that the bedroom is empty. pull slide dorsum, then press push on top of the slide, just in forepart of the sight. This button moves a metal leafage bound that will block return spring in compressed position, allowing to remove whole slide. keeping button pressed pull the trigger and allow slide return to forward (closed) position. Yous tin can release button subsequently that, spring should exist held compressed now. Yous should see it because disassembly button will now motility freely, not held by foliage bound. pull the trigger, then the hammer is in released position (upwards), otherwise it will non exist possible to complete the next step. at present the trickiest part. Expect at the grip - the back section of the grip is actually inserted into the grip. Top of it is engaged with slide and trigger mechanism, but if yous followed previous steps, information technology should exist possible to remove it now. Do not attempt to remove screw at the back of grip! Push back office of the grip (mainspring housing) slightly upwards, then pull it slightly out, towards the dorsum. And so pull whole part downwardly, to remove the other end from inside of the slide. With a bit of delicate footling you should be able to complete that step. now that mainspring housing is removed, flip model upside down and simply pull the slide to the back. Information technology should not interfere with anything (except hammer that cocks during this move). It is no longer blocked by mainspring housing and can be simply removed. Why upside downward? to avert parts falling out from the slide. annotation advisedly what is within slide. Firing bar (it is a side burn down system) just sits there, not held by anything. Now you can audit and make clean slide. Pay attention to the forepart side and firing bar. Make sure there is no water inside, metal parts will rust! At the last picture higher up see top of the mainspring housing. You lot tin see that the plunger is held by a pin. Two of the holes under firing bar take inserts from a piece of plastic tubing. This is to make impact softer and preserve slide longer. At the picture higher up note how render leap is kept compressed by a clever foliage spring. Hole in center of foliage spring is where button on top of the slide sits. Hammer down, upwards, and a view of the strut that is normally pushed by mainspring. To remove detonator pivot from the butt you need to unscrew information technology, all-time with a special cardinal supplied by MGC. This is the same central as for MGC Luger P08. Using other tools can scratch and damage detonator pin. You lot tin can maybe make out that on the left detonator pin is dingy, in the correct cleaned. Sorry for poor quality, I just couldn't figure out how to take a meliorate moving picture. If you want to perform additional inspection (not necessary during normal use), you tin can also disassemble whole mechanism: hold grips firmly together unscrew the single screw that holds both grips. Remember to hold them, there is a leafage spring inside and other parts that could fall apart. later on removing screw parts can autumn out depending on how y'all keep. I establish that it'south easier to flip model so left side is down, so remove top (right) panel offset. Underneath at that place is a leaf spring used for magazine catch. Note how this spring is placed, remove it. remove magazine release button, just press it from bottom and remove from height. at present flip model over and remove meridian (left) panel. Under the panel yous will find exposed slide lock lever and other parts. Y'all can terminate at this fourth dimension, or follow manual (posted beneath) to complete the process if you need to. When assembling back together note a few important points: brand sure all slide elements are back in right place and position: compressed jump, firing bar... before you put slide in place, erect the hammer (without spring information technology merely moves effectually) - otherwise it volition stick from frame and block slide. afterward you put slide in place release hammer by pulling trigger and pushing the strut that is inside the grip upwards. Hammer in artsy position will cake back of grip from entering its place. delicately insert back of the grip, first elevation part has to go fully within the slide, then but lock lesser role in correct identify. If something does non want to go inside, do non force it! Take time to expect, cheque, perhaps remove slide again and understand how everything should go together. Congratulations! You have at present completed disassembly and assembly of your MGC Colt Woodsman. It should work similar before, or even better if y'all cleaned and oiled it ;-) Final edited by smootik on Midweek Feb 06, 2022 3:50 pm; edited 3 times in total (Reason for editing : added photos)

c_alexandersen
Modelgun Master


Number of posts : 272
Location / Country : Kingdom of denmark
Registration engagement : 2022-eleven-30

Bailiwick: slide/breech reassemblyWed Dec 19, 2022 2:26 pm
Hi Guys I might have missed something, had a bit of a hazzle getting information technology of but for sure I cannot get it back on now ! Feel I take everything in correct place simply even so I have the collision at the pointer ! Take I missed a hint ? or

smootik
Modelgun Perfectionist


Number of posts : 1823
Location / Land : Poland
Registration date : 2009-03-03

Subject: Re: MGC Filly Woodsman Friction match Target (ABS) disassemblyThu Feb 07, 2022 4:01 pm
At present seems to be resolved after some troubleshooting. Firing bar consists of two parts that are put together (welded/glued/whatevered). The main bar, and a minor L-shaped chemical element that is at its dorsum. This L-part is where hammer strikes to button firing bar (and cartridge) forward and set off cap. It is notwithstanding not truly fixed, and can pivot around the bending signal. This means that vertical office (hit past hammer) is tilting forrard, while the horizontal part is no longer flush with the main bar. Information technology starts to protrude downwardly, eventually interfering with frame. This defect does non seem to influence normal firing and functioning, as the bar does not interfere with other parts inside. Disassembly is too possible, because due to L-function shape slide tin be pulled off. It is when assembling back that trouble happens. I establish the same defect on my Woodsman, except that the part got polished away (you can come across it on photo) and does not interfere. Solution - bend the 50-part back to be flush with the main bar, and/or file it to be more flush. Information technology remains to be verified that this gear up is working correctly. I could be guessing incorrect of course, and this L-part might have some other purpose.

folf
New Member

Number of posts : 23
Location / Country : United states
Registration date : 2022-03-xiv

Subject: Re: MGC Filly Woodsman Match Target (ABS) disassemblyFriday Mar 16, 2022 x:06 pm
Your manual is different than the one that came with mine, I really wish that one: i had a scanner and 2: i had a translation considering i cant figure out how to put some parts in and the instructions' motion-picture show doesn't really tell me what i need to know

Sponsored content

Source: https://mp40modelguns.forumotion.net/t2324-mgc-colt-woodsman-match-target-abs-disassembly

Posted by: comptonwhicily74.blogspot.com

Share this post